Before servicing the phone, please make sure that:. You use. Battery charged more than 50%. All the side programs, that may interfere with the phone, are closed. Phone’s cable and device itself should not be disconnected or disturbed until the procedure is fully completed.
![](/uploads/1/2/6/7/126701627/200130086.jpg)
Connect phone to USB port placed on the backside of PC (motherboard's USB port)Do not connect or disconnect other USB cables into the PC during the actual work with the phone. Avoid using any kind of USB HUBs and long USB cables.
Use the shortest-length USB cable available. Phone has stock (factory) firmware version. SIM card is removed. If the phone is software damaged, but can enter Fastboot mode, this feature allows you to enter Upgrade mode. Works for Huawei HiSilicon based smartphones (up to Android 9.0).
If you essentially owner a Archos 40 Neon smartphone or tablet and check for the USB driver for your device? If yes are you checking out an easy way to connect. I was going to install KDE neon on the 220Gb free. I flashed a usb drive with the lastest neon useredition (9 november 2018) using etcher from.
Important: read original phone firmware version from Fastboot mode. Open FLASH bookmark on HiSilicon tab. Select original update.app / cust.app firmware of the same version as the phone's firmware version and it's region (SD-Update files). Connect the phone in Fastboot mode (by pressing and holding Vol- and Power On).
Press 'Enter Rescue mode' button. Some Huawei firmware versions have a bug that allows you to remove FRP using 'Safe mode' method. Huawei developers are aware about this bug and it is fixed in the latest firmware versions.START:.
Enter Recovery Mode by pressing Vol+ and Power On. Check if 'Safe mode' is present in the Recovery Menu.SAFE MODE menu is present:. Perform wipe data/cache and then press 'Safe mode' menu. The phone will start in the Safe mode.
Go to the menu and select System - Reset - Reset all settings.SAFE MODE menu is NOT present in the Recovery Menu, or the previous method did not work:. You need to change the phone's firmware to the one with the bug. The easiest way is to use the flash files marked with 'Downgrade to bypass FRP'.NOTE! The flashing operation is very risky!Do the operation at your own risk. We are not responsible for any damages.This feature is intended for advanced users only.Read the phone info before flashing and use flash file with the same customization settings as is in the phone.Important!
This time we released the Flash feature for the firmwares that contain 2 files: update.app and customization.app.Firmwares of the latest Huawei models, like P30, contain 3 files.Flashing of such models is not supported Atm and will be added in the next updates. Turn the phone ON and wait until it fully starts up. Set the phone into the Manufacture Mode by entering.#.#2846579#.#. code (follow the instruction from the Enable Manufacture Mode manual). Connect the phone to PC using USB cable. Install phone (only if the phone is connected for the first time). Select 'HISILICON' platform from the tab menu in the upper left side of the software.
![Windows Windows](/uploads/1/2/6/7/126701627/798169276.jpg)
Wait for 10 seconds. Go to 'Unlock' tab. Select 'Android Adapter PCUI'. If there is no such port, select 'Comneon Mobile High-speed Modem'. Press 'Unlock' button.
The message 'Unlock done OK' indicates that procedure has been completed successfully. Disconnect the handset.
A phone is unlocked. Turn the phone ON and wait until it fully starts up. Set the phone into the Manufacture Mode by entering.#.#2846579#.#. code (follow the instruction from the Enable Manufacture Mode manual). Connect the phone to PC using USB cable. Install phone (only if the phone is connected for the first time).
Select 'HISILICON' platform from the tab menu in the upper left side of the software. Wait for 10 seconds. Go to 'IMEI' tab. Select 'Android Adapter PCUI'.
If there is no such port, select 'Comneon Mobile High-speed Modem'. Enter IMEI number in the 'Phone IMEI' field. Press 'Repair IMEI' button. The message 'Done' indicates that procedure has been completed successfully. Wait for the message 'Restarting phone. Done' to appear in Sigma dialog window; only after that you can turn the phone off. If the program asks you to perform Factory Data Reset via phone's menu, please do so.
Turn the phone ON and wait until it fully starts up. Set the phone into the Manufacture Mode by entering.#.#2846579#.#. code (follow the instruction from the Enable Manufacture Mode manual). Connect the phone to PC using USB cable. Install phone (only if your phone is connected for the first time). Select 'HISILICON' platform from the tab menu in the upper left side of the software.
Wait for 10 seconds. Go to 'Service' tab. Select 'Android Adapter PCUI'. If there is no such port, select 'Comneon Mobile High-speed Modem'.
Press 'Get Huawei Bootloader Password' button. The code will be read immediately. Disconnect the handset. Enable Manufacture Mode. Open the hidden device menu: dial '.#.#2846579#.#.' .
Select 'Project Menu' - 'Background Settings' - 'USB Ports Settings' - 'Manufacture Mode'Procedure. Internet connection has to be enabled, proxy disabled. Root is not required. Select 'HISILICON' platform from the tab menu in the upper left side of the software. 'Phone model' dropdown box has to be set to 'Autodetect'.
Go to 'Service' tab. Power the phone ON and connect it to PC with USB cable. Install required (only if the phone is connected for the first time). Select 'Android Adapter PCUI' port. Press 'FRP remove / Huawei ID' button. Enable Manufacture Mode.
Open hidden device menu: dial '.#.#2846579#.#.' . Select 'Project Menu' - 'Background Settings' - 'USB Ports Settings' - 'Manufacture Mode'Procedure.
Internet connection has to be enabled, proxy disabled. Root is not required. Select 'HISILICON' platform from the tab menu in the upper left side of the software. 'Phone model' dropdown box has to be set to 'Autodetect'. Go to 'IMEI' tab and tick “Huawei”. Connect your device to PC with USB cable. Install required (only if the phone is connected for the first time).
Select 'Android Adapter PCUI' port. Enter Wi-Fi, Bluetooth or Serial number in the required fields. Press 'Repair' button. Message 'Done' indicates that the procedure has been completed successfullyFlash. Read original phone firmware version from Fastboot mode or in the phone's menu. Open FLASH bookmark on HiSilicon tab.
Select the same or higher update.app version as the phone's firmware version. Enter Upgrade mode: press VOL+ and VOL- buttons and connect USB cable. In case the phone does not enter Upgrade mode, try to enter it using 'Rescue mode entering' manual.
Press 'Enable downgrade' button and wait for the operation to finish.After the operation, the phone will stay in the upgrade mode and will be ready for downgrading.You may reflash the phone using needed flash file version.NOTE! The downgrade operation is very risky!Do the operation at your own risk. We are not responsible for any damages.This feature is intended for advanced users only! This feature is intended to be used for phones that won’t turn on, freeze on logo, etc., but still can enter fastboot mode. It's not intended for regular reflashing.Procedure:. Connect the phone in fastboot mode (vol- power ON) to PC. Select corresponding update.app firmware file and revive the device with Sigma.
When the phone starts up normally, reflash it in UPGRADE mode using the corresponding to it flash fileIt's possible to flash Huawei Factory flash files via fastboot mode. This feature is applicable only for flashing Factory Firmware files in FastBoot mode (NOT for factory fastboot and not for HUAWEI USB COM 1.0 cases).Procedure:.
Set the phone to fastboot mode. Select Factory Flash File. Tick the box “Authorize”. Flash the Factory Flash FileBenefits:.
![Comneon Usb Driver Comneon Usb Driver](https://freeandroidroot.com/wp-content/uploads/2016/04/Root-Micromax-Bolt-A36-Using-iRoot.jpg)
Full/partial write of firmware partitions. FAST direct firmware write via fastboot mode. Flash of regular update.app files to devices with locked bootloader. Possible to use original flash files from open sources, e.g. SD-card should be removed from the phone. Press vol+vol- and connect USB cable to enter the Upgrade mode.
Open HiSilicon tab and go to Flash bookmark. Select PCUI or DBA adapter port (different phone models show different ports) in the port selection tab.
Select required update.app flash file (1). If the phone is new, the drop-down menu (2) with localization/customization files will appear (as shown on ). Select the 2 nd file in that drop-down menu.Note! Chosen file must be in the folder and unpacked.
In case the phone does not enter Upgrade mode, try to enter it using Rescue mode entering manual. Press “write flash”. Perform Wipe Data/Cache via phone's recovery (enter recovery by pressing and holding VOL+ and Power On)Important! All partitions of the firmware will be written to the phone in Upgrade mode.New smartphone models have two flash files: main flash file and localization file. These two files should be flashed together.
Use this guide only for cases, when phone is bricked and doesn’t show any devices while connected to PC, or shows HUAWEI USB COM 1.0 device (VID12D1 PID3609).Important notes:. Drivers for device. Factory flash files: - Downloads - Sigma - Huawei - Factory Flash files. Please, don’t use Factory Flash files for flashing via fastboot modeProcedure:. Device has to be set to FACTORY mode.
It should be detected as HUAWEI USB COM 1.0 in the System. In some cases Testpoint has to be used to force the device to FACTORY mode. Repair the device using Board Software file (.skf format) taken from boot-loader flash file area.After choosing the file, you may either manually select partitions to write, or select one of 4 available profiles:.
Don't flash: nothing will be flashed to the device. Just fastboot is loaded into RAM. Only FastBoot: flash only fastboot partitions. Partial flashing: main partitions will be flashed.
Full flashing: all partitions from the board software will be flashed.Warning: when selecting Full flashing mode, you may additionally select factory calibrations areas. But keep in mind that after flashing factory areas, phone’s network and other functions may become unavailable! Last updated on April 20th, 2018. Emails and Electronic CommunicationWe offer you to subscribe to our newsletters. If you no longer wish to receive correspondence, emails, or other communications from us, you may opt-out.
To do this click Unsubscribe in newsletters you are receiving from us.Most of all, we value your privacy. We do not sell, rent, loan, or give your email address or other personal information to anybody without your express permission. Collection of InformationHere are the types of information we collect: The information you give usWe receive and store any information you enter on our website or give us in any other way. We use the information that you provide for such purposes as responding to your requests, customizing future shopping for you, improving our service, and communicating with you. Log dataWe collect information that your browser sends whenever you visit our website. This log data may include information such as your computer’s Internet Protocol (“IP”) address, browser type, browser version, the pages of our Site that you visit, the time and date of your visit, the time spent on those pages and other statistics.
In addition, we may use third-party services such as Google Analytics that collect, monitor and analyze this type of information in order to increase our Site’s functionality. These third-party service providers have their own privacy policies addressing how they use such information.When you browse a website on a mobile device, we may collect certain information automatically, including, but not limited to, the type of mobile device you use, your mobile device’s unique device ID, the IP address of your mobile device, your mobile operating system, the type of mobile Internet browser you use, your location information and other statistics. CookiesCookies are files with small amount of data, which may include an anonymous unique identifier. Cookies are sent to your browser from a website and stored on your computer's hard drive.Like many sites, we use cookies to collect information. You can instruct your browser to refuse all cookies or to indicate when a cookie is being sent.
However, if you do not accept cookies, you may not be able to use some portions of our Site.We also use tracking information to determine which areas of our site users like and do not like based on traffic to those areas. Use of InformationWe use your personal information for the following purposes: to administer and improve the site and related services, to notify you of our products, services, promotional events or special offers that you may be of interest to you, etc.
AffiliatesWe may share your information with our affiliates, in which case we will require those affiliates to honor this Privacy Policy. Affiliates include our parent company and any subsidiaries, joint venture partners or other companies that we control or that are under common control with us. Security of InformationWe are committed to protecting customer personal information.The security of your Personal Information is important to us, and we strive to implement and maintain reasonable, commercially acceptable security procedures and practices appropriate to the nature of the information we store, in order to protect it from unauthorized access, destruction, use, modification, or disclosure. However, please be aware that no method of transmission over the internet, or method of electronic storage is 100% secure and we are unable to guarantee the absolute security of the Personal Information we have collected from you. Changes to this Privacy PolicyWe will occasionally update this Privacy Policy.
When we do, we will also revise the 'last updated' date at the top of the Privacy Policy.
After I reboot, Windows at first starts to install the drivers but than immediately gives an error message that the device driver was not successfully installed, again listing the hard drive as an unknown device. What can I do with a Blu Ray Frequent BSODs while gaming after BB code is on. Bumping thread since there was no reply.Uploader:Date Added:19 May 2004File Size:50.57 MbOperating Systems:Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/XDownloads:80852Price:Free.Free Regsitration RequiredSearch this Thread Advanced Search. Today I have bought a new PC with windows 7 installed on it. Western Digital Passport Portable Hard Drive Wd1200xms BlackFrequent BSODs while gaming after I plugged in my Western Digital external. All times are GMT Is there any hope for it or should i give digitxl and conclude the drive is dead? It opened without any problem, saved the data and now I have a spare 2.
BSOD, no idea what is causing it. Western digital wd1200xms-00I accepted the check and it went smoothly finding no errors or bad sectors. Originally Posted by dai.Copyright -Tech Support Forum.
Also an update – when i plug the drive in it lights up but it western digital wd1200xms-00 appear as a separate drive on windows at all, like it doesn’t exist. Posting your PC specs will help us to assist you quicker and effectively.Originally Posted by dai westerh you use the safe to remove western digital wd1200xms-00 disconnecting it.
What can I do with a Blu Ray The time western digital wd1200xms-00 is I plugged in my Western Digital external hard drive wdxms model code and everything worked fine, I was able to transfer files with no problem – until Windows 7 asked me if i want to do a disk check for errors on my drive. Half an hour latter when i plugged it back in Windows westerrn would no longer recognize it, failing to open or read it at all, giving me a “drivers could not be installed” and “device not recognized” as well as “Windows has stopped this device because it has reported problems” message under the menage devices tab.Does the device show in Disk Management? I transfered what i needed at the moment and western digital wd1200xms-00 i unplugged the device. Also i used a program called “USBDeview” but it failed to identify the drive as well it just listed it as an unknown device even western digital wd1200xms-00 this program managed to find records of the drive being used before it stopped working properly – the program gives you a list of all usb devices attached to your pc, past or present.Win 10 Italian version OS The only that shows up is the error message.
Western Digital Passport Portable Hard Drive Wdxms Black eBayBB code is on. Originally Posted by Tyree.
Damage done to Windows by Malware. Already done that, doesn’t western digital wd1200xms-00 anything.
Remove Advertisements Sponsored Links. Bumping thread since there was no reply. Thx for the help western digital wd1200xms-00. I than tried to open the external hard drive on my old computer which has Windows Xp but it again failed to open, western digital wd1200xms-00 me the same messages as Windows 7 did and I must point that i was using this drive on the Windows xp Pc for years without any problem, until this day, when i for the first attempted to open it with Windows 7 I western digital wd1200xms-00 tried it on a couple of other PCs but with no success at all, always getting the same error message – “device not recognized”.Can anybody help me please? After I reboot, Windows at first starts to install the drivers but rigital immediately gives an error message that the device driver was not successfully installed, again listing the hard drive as an unknown device.
![](/uploads/1/2/6/7/126701627/200130086.jpg)